📝 배운 내용은 다음과 같다.
📝 Topology를 구성하시오.
✨ Topology 구성도
✨ PC 설정
👉 Configuring VPC IP
VPCS>ip 192.168.33.10 255.255.255.192 192.168.33.1
ip / subnet mask / network add
✨ Switch 설정
👉 Configuring VTP Modes
🖋 server(SW3)
Switch(config)#vtp domain test
🖋 Client(SW4,SW6)
Switch(config)#vtp mode client
🖋 transparent(SW5)
Switch(config)#vtp mode transparent
👉 Configuring Vlan
Switch(config)#vlan 10
Switch(config-vlan)#name vlan10
Switch(config-vlan)#vlan 20
Switch(config-vlan)#name vlan20
🖋 configuring vlan port
🖋 SW5
Switch(config)#int e0/0
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config)#int e0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config)#int range e0/2-3
Switch(config-if-range)#switchport trunk encapsulation dot1q
Switch(config-if-rnage)#switchport mode trunk
👉 Trunk encapsulation
🖋 SW3
Switch(config)#int range e0/0,e0/2-3
Switch(config-if-range)#switchport trunk encapsulation dot1q
Switch(config-if-rnage)#switchport mode trunk
👉 Configuring EtherChannel
🖋 SW3
Switch(config)#int e0/1, e1/0
Switch(config-if-range)#channel-group 1 mode desirable
Switch(config-if-range)#exit
switch(config)# int po 1
switch(config-if)#switchport trunk encapsulation dot1q
switch(config-if)#switchport mode trunk
switch(config-if)#switchport trunk allowed vlan 1,10,20,30
✨ Router 설정
👉 Configuring IP Address
🖋 R1
Router(config)#int e0/0
Router(config-if)#ip add 192.168.33.253 255.255.255.248
Router(config-if)#no shutdown
👉 Configuring an HSRP Standby
🖋 R1
Router(config)#int e0/1
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#int e0/1.10
Router(config-subif)#encapsulation dot1q 10
Router(config-subif)#ip add 192.168.33.9 255.255.255.192
Router(config-subif)#standby 10 ip 192.168.33.1
Router(config-subif)#standby 10 priority 150
Router(config-subif)#standby 10 preempt
Router(config)#int e0/1.20
Router(config-subif)#encapsulation dot1q 20
Router(config-subif)#ip add 192.168.33.98 255.255.255.192
Router(config-subif)#standby 20 ip 192.168.33.65
Router(config-subif)#standby 20 priority 120
Router(config-subif)#standby 20 preempt
🖋 R2
Router(config)#int e0/1
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#int e0/1.10
Router(config-subif)#encapsulation dot1q 10
Router(config-subif)#ip add 192.168.33.11 255.255.255.192
Router(config-subif)#standby 10 ip 192.168.33.1
Router(config-subif)#standby 10 priority 120
Router(config-subif)#standby 10 preempt
Router(config)#int e0/1.20
Router(config-subif)#encapsulation dot1q 20
Router(config-subif)#ip add 192.168.33.99 255.255.255.192
Router(config-subif)#standby 20 ip 192.168.33.65
Router(config-subif)#standby 20 priority 150
Router(config-subif)#standby 20 preempt
👉 Configuring OSPF
🖋 R1
Router(config)#route ospf 1
Router(config-router)#network 192.168.33.0 0.0.0.63 area 0
Router(config-router)#network 192.168.33.64 0.0.0.63 area 0
Router(config-router)#network 192.168.33.248 0.0.0.7 area 0
🖋 R2
Router(config)#route ospf 1
Router(config-router)#network 192.168.33.0 0.0.0.63 area 0
Router(config-router)#network 192.168.33.64 0.0.0.63 area 0
Router(config-router)#network 192.168.33.248 0.0.0.7 area 0
🖋 R14
Router(config)#route ospf 1
Router(config-router)#network 11.11.11.0 0.0.0.63 area 0
Router(config-router)#network 22.22.22.0 0.0.0.63 area 0
Router(config-router)#network 192.168.33.248 0.0.0.7 area 0
👉 ping 결과
11.11.11.11에서 192.168.33.100 ping 결과
